Essential details
MOQ:1000L
Shipping:Express, sea freight
Product Introduction
Product Introduction:
At present, most of the solvents and diluent solvents used in flux belong to volatile organic compounds (VOC), because VOC has pollution to the environment, and flammable and explosive, the use of unsafe, so Huaihui company invested a lot of manpower and material resources to develop G-722# series of water-based halogen-free wash flux. This series of products with high purity deionized water as the main solvent, no VOC, to overcome the shortcomings of VOC as a solvent, to meet the requirements of environmental protection, non-toxic to the human body, is a new environmentally friendly lead-free free cleaning flux.
At present, most of the solvents and diluent solvents used in flux belong to volatile organic compounds (VOC), because VOC has pollution to the environment, and flammable and explosive, the use of unsafe, so Huaihui company invested a lot of manpower and material resources to develop G-722# series of water-based halogen-free wash flux. This series of products with high purity deionized water as the main solvent, no VOC, to overcome the shortcomings of VOC as a solvent, to meet the requirements of environmental protection, non-toxic to the human body, is a new environmentally friendly lead-free free cleaning flux.
Product features:
1, no halogen.
2, no VOC solvent.
3, good weldability, full and bright solder joints, good insulation.
4, low solid content, less residue after welding.
5, through the strict copper mirror test and surface impedance test
1, no halogen.
2, no VOC solvent.
3, good weldability, full and bright solder joints, good insulation.
4, low solid content, less residue after welding.
5, through the strict copper mirror test and surface impedance test
Scope of application:
Suitable for: computer and peripheral products, telecommunication products, MP3, precision instruments, digital products, etc.
Suitable for: computer and peripheral products, telecommunication products, MP3, precision instruments, digital products, etc.
Note:
1, water-based flux is deionized water as a solvent, the boiling point of water is 100 ° C, so the preheating temperature is required to be above 100 ° C, and the water is completely evaporated in the preheating zone
Drop to prevent the appearance of tin beads after the tin.
2, because the surface tension of water is large, the specific gravity is higher than VOC, it is easy to drip from the PCB, so it is required to spray, the fog point should be fine, and the spray should be uniform, such as flux on the PCB
The uneven spread on the top will result in solder leakage and tinning.
3. When foaming is used, the flux is used for a period of time due to the consumption of active ingredients leading to a decline in activity, which should be adjusted appropriately with the flux stock solution, and according to the specific
The flux is updated regularly for process conditions.
4. After opening, the flux should be sealed and then stored. The used flux should not be poured into the original packaging bucket to ensure the cleanliness of the original solution.
5. The discarded flux needs to be handled by a special person, and can not be dumped at will to pollute the environment.
6. It is strictly prohibited to add other diluents not produced by the company or mix other brands of flux in the operation to prevent chemical structure mutation, resulting in inability to clean up
The consequences of...
7. Other precautions please refer to the material safety specification table (MSDS) provided by the company.
8, when using, please customize the most suitable procedure or control method according to the process requirements to ensure the stability of quality.
9. The information provided by the company is for reference only and does not serve as the basis for taking legal responsibility. If there is any change, it will not be notified.
1, water-based flux is deionized water as a solvent, the boiling point of water is 100 ° C, so the preheating temperature is required to be above 100 ° C, and the water is completely evaporated in the preheating zone
Drop to prevent the appearance of tin beads after the tin.
2, because the surface tension of water is large, the specific gravity is higher than VOC, it is easy to drip from the PCB, so it is required to spray, the fog point should be fine, and the spray should be uniform, such as flux on the PCB
The uneven spread on the top will result in solder leakage and tinning.
3. When foaming is used, the flux is used for a period of time due to the consumption of active ingredients leading to a decline in activity, which should be adjusted appropriately with the flux stock solution, and according to the specific
The flux is updated regularly for process conditions.
4. After opening, the flux should be sealed and then stored. The used flux should not be poured into the original packaging bucket to ensure the cleanliness of the original solution.
5. The discarded flux needs to be handled by a special person, and can not be dumped at will to pollute the environment.
6. It is strictly prohibited to add other diluents not produced by the company or mix other brands of flux in the operation to prevent chemical structure mutation, resulting in inability to clean up
The consequences of...
7. Other precautions please refer to the material safety specification table (MSDS) provided by the company.
8, when using, please customize the most suitable procedure or control method according to the process requirements to ensure the stability of quality.
9. The information provided by the company is for reference only and does not serve as the basis for taking legal responsibility. If there is any change, it will not be notified.
Product details
